To reset BCM on Ford F150 cars, you can do this either by battery hack or the scan tool. Well, you can reset it by detaching and reconnecting the battery cables before waiting for 15 minutes. Or, use a scan tool like FORScan and follow the on-screen instructions to reset BCM.
In both ways, you can reprogram the Body Control Module (BCM) that controls and monitors the electronic system of your F150 car.
I’ll break down the procedure in two different sections covered in this guide. You’ll find the whole process step-by-step to follow comfortably. Let’s Go!
Table of Contents
Resetting BCM on Ford F150!
Reprogramming the BCM won’t take long if you have the right instruction. Follow the given methods to know exactly how to reset body control module F150:
Method #1: Using Battery
For a Ford F150 body control module reset, you can do it by disconnecting the battery terminals for some minutes and then reconnecting them. Let me share the procedure below:
- Start by locating the battery terminals under the hood of your F150.
- Then, use the appropriate tools to loosen and remove the cables. Be sure you disconnect both the positive (+) and negative (-) terminals.
- Once the battery is disconnected, wait for several minutes. Based on Vehicle History, you should wait up to 15 minutes. This will allow the BCM to reset fully. During this time, any residual charge in the car’s electrical system dissipates.
- After the waiting period, reconnect the battery cables in the reverse order from which you disconnected them. To put it clearly, begin with the negative (-) cable and then connect the positive (+) cable. Just be sure the connections are secure.
- After that, start your Ford F-150 car like you do. If it doesn’t start or show an issue, fix it by checking this guide.
- Next, allow the car to run for an hour to ensure the BCM reset and initializes properly.
Method #2: Using FORScan or Scan Tool
Resetting the BCM in your F150 via FORScan or other scan tools can be straightforward when done correctly. Here’s how you can do it:
- To start with, plug your OBD-II adapter into the port in your car.
- Then, connect your laptop to the adapter and open the FORScan software. In most cases, you’ll need to go to Module Programming > BCM > follow the on-screen instructions to reset it. If you have a different type of scan tool, go to the next step.
- After that, put your car key into the ignition and turn it to the ON position.
- Next, open FORScan on your laptop and connect it to your car. Then, look through FORScan’s menu by clicking on Yes. Wait for a few seconds so it connects to your car.
- Once it’s done, hit on the lmmo status scan. This will begin the scanning process of the Electronic Control Module (ECM) and the Body Control Module (BCM).
- Now, touch on lmmo learning > Perameter Reset[Fuel] > Perameter reset. Next, you’ll need to turn the ignition on by hitting OK > Yes. Once the reset is done, click on Yes. This might take about 3 to 10 minutes.
- Then, press OK after the screen shows Learning successful message. If necessary, do another reset to finish up.
- After doing this, click on ESC.
- Next, try starting the car with the new key to ensure everything’s working. If any warning lights or issues show up, use FORScan to figure out what’s wrong and fix it.
- When you’re done, close FORScan and disconnect the OBD-II adapter from the car.
After knowing the procedure, you can wonder whether does a Ford BCM need to be programmed or not.
A Ford BCM needs to be programmed so that the car starts properly. Without having keys programmed, the car won’t run.
Ending Notes
It’s quite simple to work with when you have the instructions on how to reset BCM on the Ford F150. Even if the battery trick works, I highly suggest trying the second method as it does better.
Hope you find this guide helpful in getting rid of issues related to BCM by trying the reset. Good Luck with This Project!
Now, check this guide if you are interested in learning exactly how to reset PCM in your Ford F150 car. Start Reading Here!
