How to Turn Off ABS Light on Ford F150? [Step-by-step Guide]

Encountering the ABS warning light on your Ford F150 can be a frustrating experience, prompting a search for effective methods to deactivate it.

If you’re wondering how to turn off the ABS light on Ford F150 cars, there are specific steps you can take, such as removing ABS fuses, sensors, or the control module.

It’s okay to not be familiar with the process. In this guide, I’ll provide a detailed breakdown of the precise steps to effortlessly disable the ABS light on your vehicle. Let’s get started!

Turning Off the ABS Light on Ford F150 Cars!

To avoid getting into trouble while driving on the road, you must turn it off using the right method. You may wonder whether is it OK to drive with ABS light on or not.

It is safe to drive with ABS light on but it’s not recommended. This warning light turns on to indicate issues with the braking system.

If you are clueless about it, here’s how you can do it yourself:

Method #1: Remove ABS Fuse

By removing the ABS fuse which is inside the engine compartment fuse and relay box (under the hood), you can turn off the ABS light. Follow the given directions to do it properly:

• Firstly, open the hood of your car and locate the engine compartment fuse box.
• Next, open the cover of the fuse box and locate the ABS fuse which is 5 – 40 amp. To find this fuse, be sure to check the owner’s manual.
• After that, take out the ABS fuses with your hand or a vice grip. And, this will disable the ABS.

After pulling out the ABS fuses, you may get some warning messages on the dashboard if multiple systems are on the same fuses.

Based on one user in F150 Forum, you should hold the traction control button for 5 to 10 seconds to turn off the advanced trac and get rid of the messages.

Method #2: Detach ABS Control Module

Another way you can disable the ABS light on the Ford F150 is by removing the ABS control module. Do the following steps:

• To begin with, take off the negative terminal cable of the battery.
• Next, locate the ABS control module which is on the driver’s side under the air filter. Be sure to check the owner’s manual to get the spot easily.
• Afterward, remove the air filter and anything else in the way to reach it. You can also get to it by removing the inner fender on the driver’s side.
• Then, inspect the two connectors of the ABS module. You’ll need to focus on the big one from the main part of the car.
• After that, detach the big connector’s lock by pulling it to the side of the passenger. As you move the lock, the connector will move towards the front of the car. Ensure to move it aside carefully.
• Now, unlock the other connector’s lock which is on the side of the module in the same way.
• Once it’s done, use a T20 Torx driver to take out the 4 bolts holding the ABS module to the ABS system. Be sure to gently pull the ABS module straight up to separate it from the ABS system.
• Then, cover the exposed parts to protect them from dust or dirt.

Now, you can keep on driving with no issue of the ABS warning light popping on the dashboard. However, be sure to stay alert when driving without it.

According to Mobile Mechanic, you may find it hard to control steering in wet or slick road conditions.

Method #3: Unplug ABS Sensors

The last way you can turn off the ABS warning light is by removing the ABS sensors from the front and rear sides. Here’s how to do it yourself:

Ford F150’s ABS sensor

• Start by jacking up your car and removing the wheel with a 21mm socket. If you are curious whether your F150 wheels are interchangeable or not, check this guide out.
• After removing the lug bolts, locate and detach the ABS wire from the knuckle. To do that, you’ll need an 8mm socket to detach the bolt that holds the ABS wire. If it’s too rigid to remove, ensure to use a lubricant to loosen it up.
• Then, loosen up the ABS wire by tracking where it goes and unclip it. You’ll need to follow it up until you reach the ABS sensor which is near the fender area.
• Afterward, unclip and disconnect it. You’ll now need to pull out the wire and tie it in a safe space.
• Next, remove the caliper bracket and rotor to reach the sensor using an 18mm socket. Then, use a 5mm Allen to detach the bolt that holds the ABS sensor.
• After that, use a vice grip to detach the sensor and secure the exposed area.
• Lastly, do the same thing on the other side where the ABS sensors are to finish it up.

After doing this, you can drive the car with no internal issues. So, it’s natural to get curious and question whether is it OK to drive without ABS sensor or not.

It is OK to drive without ABS sensor. But you’ll need to be careful when driving in difficult conditions as it won’t support you in emergency situations.

Overall Thoughts

Turning off the ABS light on Ford F150 cars is super simple once you know where it gets the power to give the signal to your car’s system.

Just be sure to play safe and do the above procedure as a temporary solution. And, be certain to fix the issue that the ABS light is indicating. Hope you find this guide helpful to try out the methods mentioned above. See You Later!

Now, look at this guide that shows the ways to disable the door ajar on Ford F150 cars if you often hear the chime sound. Enjoy!